Federal Signal Vision SLR Lightbar A Whole New Vision For Improved Safety overview
Redesigned from the inside out, experience the new Vision® SLR lightbar. The distinct non-linear shape and exclusive SLR (Solaris LED Rotator) provide a maximum of 360-degrees of light output not achieved by a linear lightbar. Vision SLR maximizes light output to help clear the roadway in critical traffic intersections. It is obvious as soon as you see the Vision SLR that it was engineered for safety.
Vision SLR is available with Federal Signal's new SpectraLux™ multicolor LED technology. SpectraLux enables a single lightsource to change from any color combination of Red, Blue, Amber or White. This allows for NFPA compliance as white light in route may change to Red or Blue when park is engaged. For aerial views, each reflector features two LEDs that project light upward for easy aerial location of emergency scenes.
Full Vision SLR lightbars feature the FS Convergence Network that enables for "plug-n-play" connection reducing extensive wires for quicker installation time. The Vision SLR can be operated with Federal Signal's SmartSiren® Platinum amp/light controller, Vision controller or serial interface module.
Split Vision SLR and 3-Pod Vision SLR models have designed with discrete wire harness for familiar installation on large apparatus.
Pod replacement is as easy as one-two-three. Simply loosen one screw, twist the pod and unplug. Ideal for large fleets, the Vision SLR can be serviced in minutes without removing the lightbar from the vehicle. Seeing is believing. Contact your representative today.
All colors allowed under California Title 13 (Red, Blue, and Amber) meet or exceed the Class B requirements with any of the four reflectors used in the Valor lightbar.
All colors (Red, Blue, Amber, and White) meet or exceed the SAE J595 Class 1 requirements for directional lights with any of the four reflectors used in the Valor lightbar.
Amber meets or exceeds the SAE J845 Class 1 requirements for selective coverage devices with any of the four reflectors used in the Valor lightbar.
Red, blue, and white meet or exceed the SAE J845 Class 1 requirements for selective coverage devices with the spread or angled reflectors used in the Valor lightbar.
Red, blue, and white meet or exceed the SAE J845 Class 2 requirements for selective coverage devices with the narrow reflector used in the Valor lightbar
VALR44 - 12.0A 14.0A, with Hotfoot
VALR51 - 14.0A 16.0A, with Hotfoot
Note - Amperage for a typical loaded lightbar with all lights flashing at 50 percent duty cycle.
Operating Tem. Range
-40°C to +65°C
Dimensions (H x L x D)
VALR44 - 1.96 in (111.0 cm) x 19.8 in (50.4 cm) x 43.7 in (5.0 cm)
Valor Brochure-French Canadian
Valor Work Truck Lightbar Sheet
Valor Lightbar Installation Manual
Reset Instructions for the Valor Lightbar Controller
Installation Instructions for Valor Lightbar AirTabs
Valor Lightbar with the Hook-On Mounting Kit
Valor Lightbar with the Permanent Mounting Kit
Model MBK03H Bracket Kit for Mounting the MB1 Message Board to the Hook-Mounted Valor Lightbar
Installation Instructions for the Valor/Integrity Lightbar Dome Service Kits
Addendum to Instructions 2562360 for Six-Button Control of the Valor Lightbar
Installing the Five-Hole Hook Hardware Kit
New Lightbar Hook Kit for Ford Interceptor Utility
Serial Interface Module has been re-designed
New Amber options added to our Online Lightbar Configuration
Valor Lightbar Video
Additional Valor 6-Button Keypads Available
Valor 44 inch Lightbar Assembly
Valor 51 inch Lightbar Assembly
CALIFORNIA TITLE 13 APPROVAL
California Title 13 Approved Products Brochure
Federal Signal Vision SLR
Federal Signal Vision SLR Lightbar Flash Patterns
Federal Signal Vision SLR Lightbar Auxiliary Lighting
Federal Signal Vision SLR Lightbar with SignalMaster